Lube Notes: Motor Oil Formulation

Volume 1 Issue 2 - Lubrication

Article Index
Lube Notes: Motor Oil Formulation
Total Base Number
All Pages
lube-notes_thumb

The last issue of maxxTORQUE Lube Notes explained the regimes of lubrication including Hydrodynamic Lubrication, Boundary Lubrication and Elastohydrodynamic Lubrication. As promised, I will now talk about the formulation of motor oils and why we put all those additives in our oil. Before we get into the formulations of the motor oils, we better take a look at the functions of motor oil. If we understand what oil is doing, then we can better understand why we choose certain base stocks and additives.

Motor oil must perform the following functions:

  • Lubricate engine parts in order to prevent wear
  • Reduce friction and improve fuel economy
  • Maintain clean engine components
  • Prevent rust and corrosion
  • Minimize engine deposits
  • Provide engine cooling
  • Aid in engine starting
  • Provide ring seal for better combustion pressure

Each of these functions is vital to optimum performance as well as to the durability of the internal combustion engine. Motor oils are complex lubricating fluids carefully formulated to perform all of these functions.

Motor oil is composed of base stocks and additives. The base stocks are either petroleum or synthetic and the additives are chemicals designed to satisfy the functions listed above, depending on engine type and duty.


Five Oils Front View

Base Stocks

Base stocks are derived from two sources: petroleum (crude oil) and synthetics. Within these sources there are several levels of quality. The old saying oil is oil is simply not true and potentially misleading. All oils are classified into groups with the lowest quality oils forming Group I and the highest quality forming Group VI (Group VI oil is not used in automobiles). The amount of refining (purification) and the Viscosity Index determines where the oil falls on the scale. Presently almost all petroleum oils are being made from Group II oils. This is a significant change since, not so very long ago, most petros were Group I. Some petroleum oils are made from partially hydrocracked Group II oils. Synthetic motor oils come from Group III, IV and V oils. In a later edition of Lube Notes, I will go into greater detail on the specific differences between the various groups of base oils. For now, I just want you to know that there are levels of quality in base stocks.

After a base stock is chosen, then additives (chemicals) are selected to provide

  • anti-wear,
  • anti-foam,
  • anti-oxidation
  • detergency and
  • dispersancy
  • characteristics and to
  • neutralize acid,
  • prevent corrosion and
  • maintain viscosity.

To understand motor oil, it is necessary to take a closer look at base stock properties and these additives and how they relate to the vital functions of motor oil.


Banner


Viscosity

Viscosity refers to the resistance-to-flow of the oil and is the most critical property of a lubricating oil. Viscosity varies with temperature, being greater at colder temperatures and less at warmer temperatures; in other words, it is thicker when cold and thinner when hot. If motor oils are too viscous (thick) at engine start they make starting the engine more difficult. This is especially true of diesels. Conversely, if the oil thins too much at high temperatures, it does not provide adequate wear protection. The measure of an oil’s change in viscosity with respect to temperature is referred to as Viscosity Index (VI). The higher the VI rating, the more stable an oil’s viscosity is with regard to changes in temperature, which means an oil will thicken less at colder temperatures and will thin less at hotter temperatures. Additives, referred to as VI Improvers are used to increase the VI, making the oil less reactive to temperature changes. Petroleum oils require significantly more VI Improvers than synthetic oils because synthetics inherently possess a higher VI.

COLD TEMPERATURE PERFORMANCE

The viscosity of an oil must not be so high at cold temperatures that it inhibits starting or fails to flow to the critical lubricating points in the engine.

Pour Point, a term helpful in determining an oil’s ability to avoid these occurrences, is defined as the lowest temperature at which a fluid will flow. Petroleum oils naturally contain waxes that crystallize at low temperatures causing the oil to rapidly thicken and lose its ability to flow. Pour Point Depressants are chemicals that prevent wax crystals from joining together and thickening the oil. These chemicals are added to all petroleum oils with winter ratings, which is signified by a “W” as in 10W-30. Synthetic oils are wax free with very low pour points and so do not require pour point depressants.

HEAT REMOVAL

Motor oil removes approximately 40% of the engine heat. The radiator system removes 60% but the entire lower portion of the engine is cooled only by oil. Engine lubrication could easily be accomplished with much less oil in the crankcase but additional volume is necessary to provide oil flow for heat removal.

WEAR PROTECTION

A principal function of lubricating oil is to prevent wear. Referring back to the lubricating regimes discussed in Issue One of maxxTORQUE, boundary lubrication is the challenge in the internal combustion engine. Anti-wear additives are designed to bond to the surfaces of the metal to protect the surfaces when the lubricating film of oil cannot maintain separation of the moving surfaces. Made usually from zinc and phosphorus compounds, these anti-wear additives act as soft, solid lubricants that prevent steel-to-steel contact. Anti-wear additives create a protective film on the moving parts and are critical for protection during start up and during heavy loads.

OXIDATION

Oxygen is an extremely chemically reactive element and when it reacts with oil it produces sludge and varnish deposits and causes oil thickening. When oil operates at elevated temperatures, oxidation is accelerated. Compounds formed by the by-products of combustion and oxidized oil form acids that contribute to rust and corrosion. This corrosion process is more critical in diesel engines than gasoline. Oxidation Inhibitors are added to oil to reduce oxidation. Petroleum oils react highly with oxygen, whereas synthetics are nearly inert, and react very little with oxygen.




Search

maxxTORQUE in Print

0204_cover_small
(Available through Amazon.com)

Follow us on Twitter

Login